Unique Raspberry Pi Hybrid Tube Amplifier Add On - Raspberry Pi Forums

-

the 502hta complete redesign of highly popular 503hta. have increased size standard shield size , reduced noise floor. have added ability power pi it's own supply eliminate noise coupling pi. main features are:

  • form factor – raspberry pi ® shield w/40-pin connector
  • 24-bit dac – regarded -112db snr pcm5102 used convert i2s stream drive single
    triode tube stage @ 24-bit 192khz frame rate
  • tube rolling – 502hta supports both 6dj8 (default jj 6dj8) , 12au7 type tubes. individual
    anode bias adjustment pots plus selectable series/parallel heater configuration insure perfect setup for
    virtually tube!
  • headphone out – rugged 3.5mm jack plus selectable output resistance between 1.5, 47 , 100 ohms.
  • volume pot , gain select – high quality alps potentiometer , dual gain settings allow user
    adjust output voltage optimal level each headphone.
  • single power input option – single 24v @ 2a input powers 502hta , delivers 5v@3a pi
    via low pass noise filter. power can isolated between 502hta , raspberry pi lowest
    possible noise.
  • stand-alone option – 502hta can operated in stand-alone mode using 3.5mm line in
    jack. dedicated stand-alone version, ceres, available.
  • beautiful, clear acrylic case solid machined aluminum knob included
running kickstarter campaign significant discounts both 502hta , ceres. see here:

https://www.kickstarter.com/projects/18 ... d-tube-amp


502hta shown pi , case
image


ceres shown case
image



full disclosure - designer of 502hta , ceres , work @ pi 2 design



raspberrypi



Comments

Post a Comment

Popular posts from this blog

Error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode - Raspberry Pi Forums

-
hey everyone, i'm trying compile simple code on rpi3 using geany. code written using code::blocks on windows , working without problem. errors i'm getting are: untitled.c:33:5: error: ‘for’ loop initial declarations allowed in c99 or c11 mode , untitled.c:33:5: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 compile code understand code not problem way i'm compiling it. can give me advice? you need add 1 of suggested options compile command configured in geany, in menu.. build -> set build commands add "-std=c99" after "gcc" in compile , build boxes. (i'm looking on mint pc expect version on pi same). petero raspberrypi
Read more

class MPU6050 has no member named begin

-
hi all, as working out scripts wich me make winddirection meter gy-87 calibrate compass sensor on board. i using script "hmc5883l_calibrate_mpu6050" korneliusz jarzebski. i fault "class mpu6050 has no member named begin" /*   calibrate hmc5883l + mpu6050 (gy-86 / gy-87). output hmc5883l_calibrate_processing.pde   read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/3-osiowy-magnetometr-hmc5883l.html   git: https://github.com/jarzebski/arduino-hmc5883l   web: http://www.jarzebski.pl   (c) 2014 korneliusz jarzebski */ #include <wire.h> #include <hmc5883l.h> #include <mpu6050.h> hmc5883l compass; mpu6050 mpu; int minx = 0; int maxx = 0; int miny = 0; int maxy = 0; int offx = 0; int offy = 0; void setup() {   serial.begin(9600);   // initialize mpu6050   while(!mpu.begin(mpu6050_scale_2000dps, mpu6050_range_2g))   {     delay(500);   } how slove error? any apreciated. kind regards, ilioss what compiler complainin
Read more

missing filename after '-o'

-
i'm new writing in arduino , trying program "ultimate robot kit blue". in uploading first motor test, error message keeps coming says: avr-g++: error: missing filename after '-o' exit status 1 error compiling. invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master i've been trying robot , running quite time , appreciated! you have not installed library correctly or correct name.  however, did not post code , did not post complete message guessing.  not @ guessing.  please try again, following instructions follow. to post code and/or error messages: 1) use ctrl-t in arduino ide autoformat code. 2) paste autoformatted code between code tags (th
Read more