CS4 / Vista64 / HD4870 Flickering

-

radeon 4870 latest drivers - clean inastalled
vista 64 ultimate
cs4 extended

---------

50% of time, on loading cs4, screen flickers though redrawing elements. happens when selecting tools, menu items or editing image.

turning off opengl fixes problem image editing though screen still flickers/flashes on loading / minimising app.

no other apps on pc exhibit flashing - opengl ones.

odd.

mike,
i have same setup you. few suggestions try , out. if did sorry.

i had put in 850 watt psu 4870 work correctly. takes lot of power. cs4 puts hardware test!! 500 watt not par going on.

also check make sure there no wires touching 4870 cooling fan slow down , cause on heat. (i had sata cable rubbing fan had reposition sata cable)

i assume have seen new cooling fan rpm change addition 8.10 drivers in on drive section on ccc? have rpm set @ 40 percent. card works nice , cool @ 35c.

what computer case cooling fan wise?

run directx diagnostic tool.

.net date? when first put 4870 in ccc not display correctly. updated .net , works fine.

also there new directx run time sdk listed on microsoft. update may not system, , know tell so, won't hurt try it.

refresh rate set @ 60? mine @ 59 when installed 8.10 drivers. had change 60 in ccc.

defrag helped me lot too. don't use vista defrag. use iobit smart defrag. free , vista 64 bit too. lot faster.

event viewer in computer management may record going on too.

windows defender, advance options, have cs4 not scan. have not noticed thing or bad.

i don't have issues do. hope helps little.


More discussions in Photoshop Windows (read only)


adobe

Comments

Post a Comment

Popular posts from this blog

Error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode - Raspberry Pi Forums

-
hey everyone, i'm trying compile simple code on rpi3 using geany. code written using code::blocks on windows , working without problem. errors i'm getting are: untitled.c:33:5: error: ‘for’ loop initial declarations allowed in c99 or c11 mode , untitled.c:33:5: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 compile code understand code not problem way i'm compiling it. can give me advice? you need add 1 of suggested options compile command configured in geany, in menu.. build -> set build commands add "-std=c99" after "gcc" in compile , build boxes. (i'm looking on mint pc expect version on pi same). petero raspberrypi
Read more

class MPU6050 has no member named begin

-
hi all, as working out scripts wich me make winddirection meter gy-87 calibrate compass sensor on board. i using script "hmc5883l_calibrate_mpu6050" korneliusz jarzebski. i fault "class mpu6050 has no member named begin" /*   calibrate hmc5883l + mpu6050 (gy-86 / gy-87). output hmc5883l_calibrate_processing.pde   read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/3-osiowy-magnetometr-hmc5883l.html   git: https://github.com/jarzebski/arduino-hmc5883l   web: http://www.jarzebski.pl   (c) 2014 korneliusz jarzebski */ #include <wire.h> #include <hmc5883l.h> #include <mpu6050.h> hmc5883l compass; mpu6050 mpu; int minx = 0; int maxx = 0; int miny = 0; int maxy = 0; int offx = 0; int offy = 0; void setup() {   serial.begin(9600);   // initialize mpu6050   while(!mpu.begin(mpu6050_scale_2000dps, mpu6050_range_2g))   {     delay(500);   } how slove error? any apreciated. kind regards, ilioss what compiler complainin
Read more

missing filename after '-o'

-
i'm new writing in arduino , trying program "ultimate robot kit blue". in uploading first motor test, error message keeps coming says: avr-g++: error: missing filename after '-o' exit status 1 error compiling. invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master i've been trying robot , running quite time , appreciated! you have not installed library correctly or correct name.  however, did not post code , did not post complete message guessing.  not @ guessing.  please try again, following instructions follow. to post code and/or error messages: 1) use ctrl-t in arduino ide autoformat code. 2) paste autoformatted code between code tags (th
Read more