Crumbuino-Mega ATmega2560 Übertragungsproblem

-

hallo liebes forum!

ich habe mir vor kurzem einen crumbuino-mega atmega2560 bestellt. nun wollte ich diesen in betrieb nehmen, und die installationsanleitung von dieser seite sollte hiermit helfen:

https://www.chip45.com/products/crumbuino-mega_arduino_kompatibel_atmega2560_modul_board_usb.php

ich habe mir die datei " chip45-arduino-extension.zip" heruntergeladen und in den arduino ordner:

lokaler datenträger (c:) -> programme(x86) -> arduino -> hardware -> arduino -> avr

kopiert, wie man es sollte. (anmerkung: die "zip" datei ist noch für ältere versionen der arduino ide gemacht, wo der ordner "avr" noch nicht existiert hat.

nach dem erfolgreichen kopieren dieser daten, kann man nun unter werkzeuge -> crumbuino-mega w/ atmega2650 auswählen, und z.b das blink-programm, ebenfalls von der seite aufspielen. doch nun kommt der fehler und die ganzen warnungen.

code: [select]
warning: board arduino:avr:bt328 doesn't define 'build.board' preference. auto-set to: avr_bt328
warning: board arduino:avr:lilypad doesn't define 'build.board' preference. auto-set to: avr_lilypad
warning: board arduino:avr:pro doesn't define 'build.board' preference. auto-set to: avr_pro
warning: board arduino:avr:pro328 doesn't define 'build.board' preference. auto-set to: avr_pro328
warning: board arduino:avr:bt doesn't define 'build.board' preference. auto-set to: avr_bt
warning: board arduino:avr:uno doesn't define 'build.board' preference. auto-set to: avr_uno
warning: board arduino:avr:crumbuino2560 doesn't define 'build.board' preference. auto-set to: avr_crumbuino2560
warning: board arduino:avr:crumbuino128 doesn't define 'build.board' preference. auto-set to: avr_crumbuino128
warning: board arduino:avr:lilypad328 doesn't define 'build.board' preference. auto-set to: avr_lilypad328
warning: board arduino:avr:atmega328 doesn't define 'build.board' preference. auto-set to: avr_atmega328
warning: board arduino:avr:mini doesn't define 'build.board' preference. auto-set to: avr_mini
warning: board arduino:avr:nano328 doesn't define 'build.board' preference. auto-set to: avr_nano328
warning: board arduino:avr:mega doesn't define 'build.board' preference. auto-set to: avr_mega
warning: board arduino:avr:pro5v doesn't define 'build.board' preference. auto-set to: avr_pro5v
warning: board arduino:avr:ethernet doesn't define 'build.board' preference. auto-set to: avr_ethernet
warning: board arduino:avr:mini328 doesn't define 'build.board' preference. auto-set to: avr_mini328
warning: board arduino:avr:crumbuino328 doesn't define 'build.board' preference. auto-set to: avr_crumbuino328
warning: board arduino:avr:esplora doesn't define 'build.board' preference. auto-set to: avr_esplora
warning: board arduino:avr:diecimila doesn't define 'build.board' preference. auto-set to: avr_diecimila
warning: board arduino:avr:fio doesn't define 'build.board' preference. auto-set to: avr_fio
warning: board arduino:avr:nano doesn't define 'build.board' preference. auto-set to: avr_nano
warning: board arduino:avr:leonardo doesn't define 'build.board' preference. auto-set to: avr_leonardo
warning: board arduino:avr:mega2560 doesn't define 'build.board' preference. auto-set to: avr_mega2560
warning: board arduino:avr:atmega8 doesn't define 'build.board' preference. auto-set to: avr_atmega8
warning: board arduino:avr:micro doesn't define 'build.board' preference. auto-set to: avr_micro
warning: board arduino:avr:atmega168 doesn't define 'build.board' preference. auto-set to: avr_atmega168
warning: board arduino:avr:pro5v328 doesn't define 'build.board' preference. auto-set to: avr_pro5v328
warning: board arduino:avr:lilypadusb doesn't define 'build.board' preference. auto-set to: avr_lilypadusb
bootloader-datei angegeben, aber nicht vorhanden: c:\program files (x86)\arduino\hardware\arduino\avr\bootloaders\stk500boot_v2_crumbuino2560.hex

der sketch verwendet 1.504 bytes (0%) des programmspeicherplatzes. das maximum sind 258.048 bytes.
globale variablen verwenden 9 bytes des dynamischen speichers.
fehler beim hochladen: konfigurationsparameter 'upload.tool' fehlt


hat jemand eine idee hier falsch laufen könnte, und wie man eine lösung erzielen kann ?

lg

hallo,

leider funktioniert die chip45 ide extension nur mit älteren ide version 1.x oder so. bei der aktuellen arduino ide wurden diverse konfigurationsfiles geändert, sodass die extension nicht mehr dazu passt.

bis es eine neue extension gibt, kann das crumbuinomega als original arduino mega verwendet werden. es fehlen dann ein paar wenige ios, aber es funktioniert dann unabhängig von der extension mit jeder ide version. das infosheet gibt auch das pinout in diesem mode an.

viele grüße,
er!k


Arduino Forum > International > Deutsch (Moderator: uwefed) > Crumbuino-Mega ATmega2560 Übertragungsproblem


arduino

Comments

Post a Comment

Popular posts from this blog

Valutazione Template - Joomla! Forum - community, help and support

-
salve, prima di installare joomla, vorrei porvi tre semplici domande: 1) l'ultima versione in italiano di joomla, supporta questo template prodotto da gavik? loro scrivono che non è un semplice template, ma una vera e propria suite, ma vorrei una vostra opinione. qui sono descritte le funzioni della suite. 2) per sfruttare gli elementi che si vedono nella pagina, ad esempio quello in alto sinistra dove scorrono le notizie, occorre installare qualche componente aggiuntivo? 3) futuri upgrade alla piattaforma joomla, potranno inficiare il funzionamento o la compatibilità del template? vi ringrazio anticipatamente della disponibilità. 1) non vedo nulla di particolare se non una miriade di posizioni per blocchi 2) è un modulo se non sbaglio pagamento, ma adesso non ricordo bene 3) no. ti ricordo che devi installare joomla  1.0.12 Board index Joomla! International Language Support International Zone Italian Forum ...
Read more

SD Datastring Convention

-
i wondering if there preferred convention appending data logged?  see standard sd example uses: code: [select] void loop() {   // make string assembling data log:   string datastring = "";   // read 3 sensors , append string:   (int analogpin = 0; analogpin < 3; analogpin++) {     int sensor = analogread(analogpin);     datastring += string(sensor);     if (analogpin < 2) {       datastring += ",";     }   } creating string called datastring, , appending it, have seen in forums string not liked.  around this, code data logging looks this: code: [select] void sdupdate() {   datetime = rtc.now();   unsigned int hour = now.hour();   unsigned int minute = now.minute();   unsigned int second = now.second();   char datastring[100] = "";   char char_current_pay[15] = "";   char char_overall_pay[15] = ""; ...
Read more

First use of Arduino Uno : avrdude error on Blink uploading

-
hi all, i bought arduino (or should genuino) starter kit. first test , failing. i have follow religiously first pages , when trying upload blink sketch, uploading fails avrdude error : avrdude: stk500_recv(): programmer not responding. as suggested in other posts, have tried 1) switch latest hourly build of arduino ide 2) switch previous stable version of arduino ide (1.6.09) 3) change usb cable 1 know working fine 4) make same steps on computer (unfortunatelly, of them macos running on macos 10.11.6, not interesting test) 5) press reset before upload, interesting thing : tx led never flashes the full log attached. idea of why happening ? to save people having download log, it's sync error, resp=0x00 every time: code: [select] avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 avrdude: stk500_recv(): programmer not responding and he's running 1.6.11 hourly avrdude 6.0.1. ...
Read more