Skip to main content

Thread: 9.10 Partitioner will not give option to partition

-

trying install dual boot windows xp-home edition, have 18g available free, partitioner on live cd (direct install or desktop) not give option re-partition automatically. instead partitioner on installer says there 7mb free space (but windows says 18g) , gives me 3 options;

1. erase , use entire disk "scsi2 (0,0,0) (sda) - 30.0 gb ata hitachi_dk12ea-3"
2. use largest continuous free space
3. specify partions manually

option 3 again presents disk full , not allow me proceed changing partition size.

how installer partition hdd?

equipment
dell inspiron 1100 laptop
1g ram
intel celeron 2.2ghz
30g hdd (18g free)

quote posted michaelmcnutt view post
trying install dual boot windows xp-home edition, have 18g available free, partitioner on live cd (direct install or desktop) not give option re-partition automatically. instead partitioner on installer says there 7mb free space (but windows says 18g) , gives me 3 options;

1. erase , use entire disk "scsi2 (0,0,0) (sda) - 30.0 gb ata hitachi_dk12ea-3"
2. use largest continuous free space
3. specify partions manually

option 3 again presents disk full , not allow me proceed changing partition size.

how installer partition hdd?

equipment
dell inspiron 1100 laptop
1g ram
intel celeron 2.2ghz
30g hdd (18g free)
quick question .... 18gb free ..... unallocated space or space inside windows xp free/unused windows?

regards


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Installation & Upgrades [ubuntu] 9.10 Partitioner will not give option to partition


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode - Raspberry Pi Forums

-
hey everyone, i'm trying compile simple code on rpi3 using geany. code written using code::blocks on windows , working without problem. errors i'm getting are: untitled.c:33:5: error: ‘for’ loop initial declarations allowed in c99 or c11 mode , untitled.c:33:5: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 compile code understand code not problem way i'm compiling it. can give me advice? you need add 1 of suggested options compile command configured in geany, in menu.. build -> set build commands add "-std=c99" after "gcc" in compile , build boxes. (i'm looking on mint pc expect version on pi same). petero raspberrypi
Read more

class MPU6050 has no member named begin

-
hi all, as working out scripts wich me make winddirection meter gy-87 calibrate compass sensor on board. i using script "hmc5883l_calibrate_mpu6050" korneliusz jarzebski. i fault "class mpu6050 has no member named begin" /*   calibrate hmc5883l + mpu6050 (gy-86 / gy-87). output hmc5883l_calibrate_processing.pde   read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/3-osiowy-magnetometr-hmc5883l.html   git: https://github.com/jarzebski/arduino-hmc5883l   web: http://www.jarzebski.pl   (c) 2014 korneliusz jarzebski */ #include <wire.h> #include <hmc5883l.h> #include <mpu6050.h> hmc5883l compass; mpu6050 mpu; int minx = 0; int maxx = 0; int miny = 0; int maxy = 0; int offx = 0; int offy = 0; void setup() {   serial.begin(9600);   // initialize mpu6050   while(!mpu.begin(mpu6050_scale_2000dps, mpu6050_range_2g))   {     delay(500);   } how slove error? any apreciated. kind regards, ilioss what compiler complainin
Read more

missing filename after '-o'

-
i'm new writing in arduino , trying program "ultimate robot kit blue". in uploading first motor test, error message keeps coming says: avr-g++: error: missing filename after '-o' exit status 1 error compiling. invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master i've been trying robot , running quite time , appreciated! you have not installed library correctly or correct name.  however, did not post code , did not post complete message guessing.  not @ guessing.  please try again, following instructions follow. to post code and/or error messages: 1) use ctrl-t in arduino ide autoformat code. 2) paste autoformatted code between code tags (th
Read more