Skip to main content

Thread: Internet Connection @ LAN Party

-

hey everyone,

wondering if me out here.

basically, in jan next year running small lan party, dedicated server.

dedicated server installation of ubuntu 8.10, of ubuntu desktop removed (all gnome packages). used command found here that, didnt install kubuntu packages after. installed gdm, xorg, xfce4, synaptic, xterm, firefox, gksu. lightweight system. on there lamp installation, things autominous lan party , tunez, plus srcds , cod4 servers etc.

"dedicated server" laptop has gigabit network port on it. when run network, connecting cat6 cable laptops gigabit gigabit port on cisco 48 port switch, players connected to.

means lan working fine, wish introduce internet equation, limit on dedicated server (probably squid?) people can access sites+services. onboard laptop wlan card, connect router in room provide incoming traffic internet access.

how go bridging these connections through squid or whatever need use?

hope makes sense!!

thanks,

harrison

makes sense me! wish you, that's little out of league. think squid idea though, understand does, , sounds fits bill perfectly. regular @ website has substantial network orientation, particularly linux. check documents there, might have stuff squid in there: http://linuxhomenetworking.com


Forum The Ubuntu Forum Community Ubuntu Specialised Support Ubuntu Servers, Cloud and Juju Server Platforms [ubuntu] Internet Connection @ LAN Party


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode - Raspberry Pi Forums

-
hey everyone, i'm trying compile simple code on rpi3 using geany. code written using code::blocks on windows , working without problem. errors i'm getting are: untitled.c:33:5: error: ‘for’ loop initial declarations allowed in c99 or c11 mode , untitled.c:33:5: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 compile code understand code not problem way i'm compiling it. can give me advice? you need add 1 of suggested options compile command configured in geany, in menu.. build -> set build commands add "-std=c99" after "gcc" in compile , build boxes. (i'm looking on mint pc expect version on pi same). petero raspberrypi
Read more

class MPU6050 has no member named begin

-
hi all, as working out scripts wich me make winddirection meter gy-87 calibrate compass sensor on board. i using script "hmc5883l_calibrate_mpu6050" korneliusz jarzebski. i fault "class mpu6050 has no member named begin" /*   calibrate hmc5883l + mpu6050 (gy-86 / gy-87). output hmc5883l_calibrate_processing.pde   read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/3-osiowy-magnetometr-hmc5883l.html   git: https://github.com/jarzebski/arduino-hmc5883l   web: http://www.jarzebski.pl   (c) 2014 korneliusz jarzebski */ #include <wire.h> #include <hmc5883l.h> #include <mpu6050.h> hmc5883l compass; mpu6050 mpu; int minx = 0; int maxx = 0; int miny = 0; int maxy = 0; int offx = 0; int offy = 0; void setup() {   serial.begin(9600);   // initialize mpu6050   while(!mpu.begin(mpu6050_scale_2000dps, mpu6050_range_2g))   {     delay(500);   } how slove error? any apreciated. kind regards, ilioss what compiler complainin
Read more

missing filename after '-o'

-
i'm new writing in arduino , trying program "ultimate robot kit blue". in uploading first motor test, error message keeps coming says: avr-g++: error: missing filename after '-o' exit status 1 error compiling. invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master invalid library found in /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master: /users/dennisleary/documents/arduino/libraries/makeblock-libraries-master i've been trying robot , running quite time , appreciated! you have not installed library correctly or correct name.  however, did not post code , did not post complete message guessing.  not @ guessing.  please try again, following instructions follow. to post code and/or error messages: 1) use ctrl-t in arduino ide autoformat code. 2) paste autoformatted code between code tags (th
Read more